Toyota Alphard Camper 2004 - 53K - Ipswich Area
Rear conversion, with pop-up roof, gas hob, sink, electric hook up, full service etc Andy’s Imports March 2022
Serviced 2024 & 2025
MOT till 13/02/2026
Four new tyres fitted in February
True milage is actually lower (35.5k as was converted from km)
Wireless solar powered reversing camera
Car VX Vehicle history Report
Good clean condition
Will be advertising it eleswhere later but popping it on here first in case someone interested
£12,500
Hi I've been away so hence delay in replying. My light has now gone out??? So assuminmg due to change of tyres does something eventually adjust itself and sorts itself out?
Cheers
John
Although the light disappeared for a couple of short journeys it came back on yesterday grrr. Any suggestions as what I can do to try and sort please.
Cheers
John
I think they are the same size. I checked in the dark tonight and the lights did seem to go up and down when I started it up. Never knew it did that 😉 I don't think it has been driven in the dark since I had the tyres replaced. I will check on Thursday if light on the dash still on.
Thanks
John
Hi This light has started coming on all the time. I've checked all the lights and they seem OK. I also checked for fault codes and it didn't find any.
Any idea what is causing it and how I sort it?
Thanks
John
IMG_3723.HEIC
Firstly Thanks to Lee who advised on scanner & part this has now been sorted, could not have done it without his support!
To change the sensor i needed the following tools screwdrivewr, 12mm & 14mm sockets and spanner and a E7 spline socket.
Had to take off the heat shield to get the sensor out unfoutunately one fixings of the shield has a stud and nut and I needed to get the stud out with the spline socket. Luckily came out ok.
I undid the sensor with 22mm spanner the new one was a bit of a pain to screw in but eventually managed it. Put heat shield back on and started the engine and engine warning light is off 🙂 Great Result
Would have prefered to have done in the summer though.
Kind Regards
John
IMG_3614.HEIC
IMG_3615.HEIC
IMG_3616.HEIC
IMG_3617.HEIC
IMG_3618.HEIC
IMG_3619.HEIC
Will do - And very grateful for Lee's recomendation of scanner which worked a treat. I did email the supplyer regarding the streetwize spanner looks like if anyone wants to try it you can take it back.
Cheers
John
Good day to you.
We have learned that Japanese cars began introducing the OBD II protocol in 2000, and it wasn't until around 2006 that the OBD II protocol became popular.
Currently, we can't find this car from 2004 in China, so we can't test whether this car has the OBD II protocol.
So the consumers may need to test it themselves to see if it can be used SWOBD4. If it can't be used, the car not the OBDII protocol
I apologise that this doesn’t give you enough information for you to go on but if you were to purchase the unit and it doesn’t work you could always take it back as all our products come with a 12 month warranty and it would obviously not be fit for purpose
Well reader came to day and this is what it found. Connected and ran the engine then selected rerad fault codes.
P0135 Oxygen Sensor Heater Circuit (Bank1 Sensor1)
So the next question is what do I do now is this easy to replace?
Cheers
John
IMG_3601.HEIC
Thanks for the replies I think I'll go for the Ancel - I take it this is the connection above the pedals
- Once I get it I'll let you know how I get on
Has anyone tried one of these to check engine codes? There are in toolstation and I have the dreaded yellow/orange engine warning light up.
https://www.toolstation.com/streetwize-car-diagnostic/p12772
We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.