Skip to content

AndrewS

Members
  • Joined

  • Last visited

  1. Your reply was incredibly helpful and the good news is that the heater (and aircon) both now seem to be working> A quick recap for all the idiots like me: 1) the plastic connection to the top of the radiator: the plastic bit which has the metal radiator cap on it comprises 4 parts: the main tube (which the cap screws on to and has a narrow bit which attaches to the coolant reservoir); a soft plastic washer (fits on the tube coming off the radiator); a hard liner circle (which fits inside the connector); a separate plastic clip (which fits over the connector after you have attached it to the radiator) 2) once the connector was properly attached, I was able to put in more coolant without any leaking- not sure how significant that was 3) followed MonsterS's instructions - specifically squeezing the soft rubber hose of the radiator - it is pretty obvious which one it is I had been trying all sorts of things and watching YouTube videos - was it the heater core which needed to be flushed or removed, etc, etc. No just warming up the engine and squeezing some air out!
  2. Hi I recently had a new radiator installed and then a new condenser on my 2003 2.4 Alphard. The heater isn't working so I thought I would top up the coolant, even though the engine temperature is completely normal. When I take off the cap and pour in new coolant, the plastic connector is leaking where it connects to the top of the radiator. Surely this is supposed to be sealed? I just can't get it to fit on properly. I have no idea if this is the reason the heater isn't working, but it might just be that the coolant is low and I can't top it up. Any thoughts?
  3. I know this is a long time after these posts, but I have received penalty charge notices for my 2003 petrol Alphard in London and Edinburgh (my own stupidity) and I have actually previously paid ULEZ in London. I now realise that this is all because the Alphard is pre-2006 and the V5C does not include any emissions data. Yet, I understand that my vehicle is at least Euro 4 and I have a French Crit Air sticker 1 issued by the French government which is apparently certifying the vehicle is Euro 6! So my vehicle is ULEZ/LEZ compliant, but the data relied upon by TFL/Edinburgh City Council is defective. I also have a stack of MOTs with the emissions data recorded, but I have no idea what this data evidences - presumably that it is ULEZ/LEZ compliant! Any thoughts on how to prove that I am at least Euro 4?
  4. Hi, yes I do have phone which is why it is no big deal really. However it is just one of those irritants and I would like to sort it. Yes, I had found something about the Philippines. It is all a bit beyond my limited computer skills, so I will try and find someone who can take a look.
  5. Hi. I am still crawling towards a solution to this. I now think I understand that the navigation software on my audio unit is something called Navione. If this is loaded then it should allow me to access the maps etc for the sat nav to work. I am supposed to download Navione.exe on to the SD card (or to the unit itself. I don't seem to be able to find this Navione.exe software, though I am still looking. Does anyone else have this software and where did they get it from?
  6. So, after a bit more prising, I have discovered the SD card and the USB port behind the GPS/USB button. Not really that surprising, but thanks fo the suggestion. It is a small SD card (8GB) When I take out the SD card, I was able to progress a bit further with some other choices (Navi - says check GPS Path; GPS Path - provides some details, but it looks to be searching for the SD card; Set Up - allows me to change the time zone etc; System Info - a list of info), and, when I put it back in, it was clear that something was trying to load (the program appears to be something called iGo with a photo of Hong Kong). It loads about 50%, then greys out and fails to load. I presume I might just have to buy a new SD card unless anyone has any ideas about what might be the issue. The Warning shown on the photo says "The application failed to start last time". Perhaps it is just defective/corrupted?
  7. Where do you think the SD card might be on my version? The button SD/RST (bottom right) is just a cover. I prised it off and it is just connected by a bit of plastic. You can see the default message on the screen. When I press reset, it just fades out and reverts to the general menu. Any thoughts?
  8. Hi When I bought my Alphard 2003 a few years ago, the sat nav was working fine in the UK and, briefly, when I crossed over into France. It hasn't worked since (I have had a couple of flat battery incidents). When I select the navigation system, all I get now is a button to press (in English and Japanese) which says rest to factory default. So I press that and nothing happens, it just closes down. Any suggestions? The radio and bluetooth contine to work normally.
  9. Hi. I have put a couple of posts on here a while ago. I had a towbar fitted which cost about £400 (an Alphard needs something a bit bespoke which my fitter ordered from somewhere in Sheffield). I then bought a secondhand Thule 2 bikerack off ebay. It cost £80. It isn't the tilt type, but works very well, and I just accept I can't open the tailgate without taking the bikes off - I don't need to remove the carrier itself, since it has a foldable frame. The bike rack also doubles as a luggage carrier. Without the bikes on, I can attach a large Fiamma luggage bag which fits a huge amount of stuff. £40 off ebay.
  10. Hi Everything electrical on the van is working fine - except the passenger side electric windows (front passenger and side door) are not working - either using the driver's controls or the passenger controls. They just seem to have stopped. It is perhaps associated with the various other issues I have had with the electrics. Any ideas? Might it just be a fuse or other thoughts on what it might be? Some need to reset? Regards
  11. Hi Just thought I would update my experience, which might help someone: 1) accessing the fuse box on the passenger side is a nightmare for an amateur like me. However, with a pair of log-nosed pliers, I was able to check the relevant fuse. I am not sure if the difficulties of access were compounded by the additional electrics for the camper conversion. The manual I have says contact your Toyota dealer, so Toyota clearly know there is an issue. 2) I got no help at all from my local Toyota dealer - refused to engage. I suspect it is a bit hit and miss as to whether they can be bothered 3) I found an autoelectrician in Shipley, Luke at Drive in Service Centre on Otley Road. He diagonosed what had gone on in 10 minutes: a) nothing to do with key or immobiliser b) when the AA had recharged my flat battery there had been a usual surge as all of the electrics power up at the same time c) somebody had previously done a repair on the cable from the battery to the small fuse box under the bonnet d) the battery was fine but the surge had shorted the cable and blown one of the fuses - this accounted for why the dashboard lights were lighting up, but otherwise everything electrical was dead. e) I was told that UK Toyota diagnostics equipment can read all Toyota vehicles. Toyota could have made this assessment for me. So, back on the road, no issues, but now very careful to turn off lights (and on auto). There is no warning signal if I leave my lights on.
  12. Hi. Just an update and maybe somebody can help. I have rung round various auto electricians with very little success. Potentially the best advice is: 1) immobiliser light is flashing without key in the ignition; 2) however with the key in the ignition the light goes off - conclusion: the key is speaking to the immobiliser and so it is not an issue with the immobiliser; 3) perhaps the key is not the issue, but the central locking and some other engine cut out (eg the central locking button isn't working and neither is the key fob); 4) perhaps it is is the fuses which have blown relating to to the locking mechanism? Al sounds plausible. I now have to get at the fuse box in the passenger glove box. My manual says: "Consult your Toyota dealer when you need to check or replace fuses in this box"!
  13. Hi Thanks Paul. As far as I am aware, it is a factory immobiliser. Until the car battery went flat I haven't ever had a problem with it, including when the battery also went flat about 6 months ago. That time I didn't have to use the physical key to unlock, which is why I wondered if using the physical key this time might have made a difference. I can't rule it out, but it would seem too much of a coincidence that the induction coil has packed up at the same time as the car battery going flat. I wonder if it might be as simple as the key battery being a bit old, but again a bit of a coincidence if it is this. I will try replacing it and see what happens. Resynchronisation might be the solution. I am pleased you think the flat battery is unlikely to have casued this. My problem is that I can't get anyone to be interested: Toyota say Alphards aren't on their system; and the auto electrics garage won't look at it for 2 weeks becasue they are busy. Any thoughts on whether a locksmith would need to have specific skills to deal with this type of thing? Another possibility might be some form of electrical interference. The van was parked next to the electric railway. who knows, but once it is home, everything might work. On one video there is a suggestion that I insert the key and turn on the ignition for several minutes. Ever heard of that?
  14. Hi Does anyone have any experience about deactivating the immobiliser? I have had the AA to help me, but they have not been able to help. The scenario: I locked the van with my electronic key fob; I stupidly left the lights on and when I returned the key fob didn't work to unlock (though the light on the fob showed it was not the battery); I opened the van using the manual key; AA turned up and recharged the battery; however, the van would not start nor move out of park to neutral; the little-red-car-with-a-key light is flashing, showing that the immobilser is on; the AA guy had a gadget which showed that the key fob was not sending a signal to the immobiliser; the AA tried and tried, but didn't know how to turn off the immobiliser. The van is now on the back of an AA low loader and is being taken to home. It will have to stay there until either 1) I work out how to deactivate the immobiliser (and Toyota and nobody else seems to be able to tell me); or 2) a get it moved to an auto electrician in 2 weeks when they can next look at it. Anyone any ideas?! Surely it must be pretty easy to repreogramme the key or whatever? Thanks in advance.
Background Picker
Customize Layout

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.